Home Page
Barbecues
Charts & Publications
Dock Stuff
Engine Parts
Featured Products
Hardware
MacGregor 26
MacGregor Parts
Marine Care
MOOR Electronics
Nautical Gifts
Online Electronics Specials
Online Footwear Specials
Online Store Specials
Plumbing
Seating
Tattoo 26
Winterizing & Storage
|
|
All prices are in Canadian dollars --
convert to my currency
|
To bring up a large picture of Floating Dock Hardware, please click here. |
|
911123 - HD Connector Hinge is used at both ends of a ramp when connecting a
dock section to shore; where extreme wave action is encountered, or in
joining large or multiple sections together where this join could act
as a fulcrum or pivot point. 1/4" Hot Dipped Galvanized Steel. $84.99 #911123
|
|
921043 - Inside Corner is
used in lighter duty applications where an outside
corner is not necessary. It is also used to replace a 990023 Joist
Corner in heavier duty applications. 1/4" Hot Dipped Galvanized
Steel. $18.49 #921043
|
|
921163 - Inside Anchor Corner is used in the same applications as a 921043 Inside Corner but
offers extra strength with its anchor chain bar. Accommodates chain up
to 1/2". 1/4" Hot Dipped Galvanized Steel. $14.99 #921163
|
|
921243 - 45 Degree Corner is used with a 961083 135 DEGREE CORNER to construct finger
stabilizers or to construct a custom V-Shaped Berth for the bow of your
boat. 1/4" Hot Dipped Galvanized Steel. $39.49 #921243
|
|
931223 - Backer Plate must be used to sandwich the wood framing when another piece of hardware
is not used. This prevents the bolts from working into the wood and the
lock washers becoming undone. 1/8" Galvanized steel plate. $7.49 #931223
|
|
961083 - 135 Degree Corner is used with a 921243 45 DEGREE CORNER to construct finger
stabilizers or to construct a custom V-Shaped Berth for the bow of your
boat. 1/4" Hot Dipped Galvanized Steel. $25.29 #961083
|
|
961113 - Connector Pin is used to join Male and Female Connectors. $9.99 #961113
|
|
990013 - HD Anchor Chain Corner
offers maximum corner strength when used with a 990043 Outside Corner
or any Corner Connecting Hinge. 1/4" Hot Dipped Galvanized Steel.
$34.99 #990013 |
|
990023 - Joist Corner is used to mount stringers with 990063 Washer Plates. It can also be
used as a backer on the inside edges of the dock to prevent cleats from
pulling out. 1/4" Hot Dipped Galvanized Steel. $9.99 #990023 |
|
990043 - Outside Corner is used at outside ends of docks, fingers and swim platforms and in
conjunction either with a 990013 HD Anchor Chain Corner or 931223 Backer
Plates, depending on the strength required. 1/4" Hot Dipped Galvanized Steel. $29.49 #990043
|
|
990053 - Side Pipe Holder bolts to side frame of the dock to anchor it in place while allowing for vertical
movement due to water level fluctuations. Use 990063 Washer Plates on
opposite side. 1/4" Hot Dipped Galvanized Steel. $45.99 #990053
|
|
990063 - Washer Plate is used on a 990133 Chain Retainer, 990053 Side Pipe Holder and 990023
Joist Corner. 1/4" Hot Dipped Galvanized Steel. $4.99 #990063
|
|
990073 - Inside Corner Pipe Holder
with slotted holes for various wood thickness. Use with 990043 Outside
Corner or Outside Corner Connector Hinges. 1/4" Hot Dipped Galvanized
Steel. $69.99 #990073
|
|
990093 - Male Corner Hinge can be used with all styles of Female Connector Hinges. For inside
corner support, match with 990013 HD Anchor Chain Corner for
maximum strength or two 931223 Backer Plates. 1/4" Hot Dipped Galvanized Steel. $40.99 #990093
|
|
990103 - Female Corner Hinge see 990093 Male Corner Hinge above. 1/4" Hot Dipped Galvanized Steel. $44.49 #990103
|
|
990113 - Female T Connector see 990123 Male T Connector below. 1/4" Hot Dipped Galvanized Steel. $19.99 #990113
|
|
990123 - Male T Connector can be used with all styles of Female Connector Hinges. For inside
corner support, match with 921043 Inside Corner, 921163 Inside
Anchor Corner, or 990013 HD Anchor Chain Corner. May
also be placed anywhere on the side of the dock with a 931223 Backer
Plate for attaching fingers and ramps. 1/4" Hot Dipped Galvanized Steel. $15.99 #990123
|
|
990133 - Chain Retainer
bolts to side of the dock and uses chain up to 1/2" to secure the dock
in place. Use with 990063 Washer Plates. 1/4" Hot Dipped Galvanized
Steel. $32.99 #990133
|
|
992413 - Foamed Filled 400 Dock Float
- Foam filled for commercial use. Rotational Molded from high density
black virgin polyethylene with UV inhibitors ensuring the most rugged
float possible. Wall thickness is a minimum 5/16" and up to 1/2" at
fastening points and corner edges, ensuring extremely strong resistance
to splits and punctures. Flotation capacity is 400 lbs. with overall
dimensions of 24" x 48" x 12" high. $209.99 #992413
|
|
992423 - 400 Dock Float - Rotational Molded from high density black
virgin polyethylene with UV inhibitors ensuring the most rugged float
possible. Wall thickness is a minimum 5/16" and up to 1/2" at fastening
points and corner edges, ensuring extremely strong resistance to
splits and punctures. Flotation capacity is 400 lbs. with overall
dimensions of 24" x 48" x 12" high. $149.99 #992423
|
|
992463 - 550 Dock Float - Rotational Molded from high density black
virgin polyethylene with UV inhibitors ensuring the most rugged float
possible. Wall thickness is a minimum 5/16" and up to 1/2" at fastening
points and corner edges, ensuring extremely strong resistance to
splits and punctures. Flotation capacity is 550 lbs. with overall dimensions of 24" x 48" x 16" high. $231.99 #992463
|
|
To bring up a large picture of Stationary Dock Hardware, please click here.
|
|
861003 - Corner Leg Holder mounts on the inside corner of the frame. 1/8" Hot Dipped Galvanized Steel. Stainless Steel bolts. $17.49 #861003
|
|
861013 - Side Leg Holder
can be mounted on the inside or outside of the dock frame. 1/8" Hot
Dipped Galvanized Steel. Stainless Steel bolts. $14.49 #861013
|
|
861023 - Base Plate
is used as a footing. It may be bolted to a 2" x 6" piece of lumber and
joined to an adjacent leg Base Plate for increased stability. 1/8" Hot
Dipped Galvanized Steel. Stainless Steel bolt. $13.99 #861023
|
|
861033 - Connector Hinge is used to easily join sections of the dock together. Also accommodates
joining a fixed ramp to the dock at varying angles. Hinge Pin included. 1/8" Hot Dipped Galvanized Steel. $20.99 #861033
|
|
861043 - Corner Plate is mounted on inside corners for increased corner strength. 1/8" Hot Dipped Galvanized Steel. $11.49 #861043
|
|
871073 - Corner Leg Brace Holder
is used when running a 891013 Leg Brace Set at right angles from a
corner leg to two side legs for optimum stability. 1 Pc. /Bag, Bolts
Included. 1/8" Hot Dipped Galvanized Steel. $12.49 #871073
|
|
871223 - Backer Plate
is used per guide. Prevents pipe from compressing into the wood
resulting in dock sliding down the leg pipe. Also prevents bolts from
working into the wood and the lock washers coming loose. 1/8" Hot
Dipped Galvanized Steel. 7/16" holes for 3/8" Carriage Bolts. $7.49
#871223
|
|
891013 - Leg Brace Set contains two outer links and one inner link. Extends up to 72" and is
used with 931053 Leg Brace Holder and/or 871073 Corner Leg Brace
Holder to connect legs for maximum stability. $31.99 #891013
|
|
911113 - Plastic Leg Caps contain UV Inhibitors and cover raw leg pipes edges for safety. Also
adds a finishing touch to the dock. 4/ Pkg. $6.99 #911113
|
|
911163 - Anchor Tie Down Corner is used to help secure the dock in place if required in rough water
conditions. May also replace 861043 Corner Plate when extra strength
is required. 1/8" Hot Dipped Galvanized Steel. 7/16" holes for 3/8" Carriage Bolts. $14.99 #911163
|
|
931053 - Leg Brace Holder is used with 891013 Leg Brace Set to connect legs
together for maximum stability. 1 Pc. /Bag with Header, Bolts Included. 1/8" Hot Dipped Galvanized Steel. $31.99 #931053
|
|
931103 - Galvalume Leg Pipe is a heavy wall steel with 10 times the corrosion resistance of normal
steel and 2 times the corrosion resistance of Hot Dipped Galvanized
Steel. 1.9 Gauge, 1 7/8" O.D. Length: 10'. $75.49 #931103
|
|
931683 - Galvalume Leg Pipe is a heavy wall steel with 10 times the corrosion resistance of normal
steel and 2 times the corrosion resistance of Hot Dipped Galvanized
Steel. 1.9 Gauge, 1 7/8" O.D. Length: 6' 8". $50.99 #931683
|
|
941023 - Bottom Pad with its large surface area is used in soft bottom areas. The leg pipe
can extend through the pad into lake bottom for extra lateral support.
The pointed corners also grab when the bottom is rocky. 1/8" Hot Dipped Galvanized Steel. $32.99 #941023
|
|
951223 - Joist Corner
is used to reinforce stringer plates. 1/8" Hot Dipped Galvanized Steel.
7/16" holes for 3/8" Carriage Bolts. $8.49 #951223
|
|
Dock Bumper Double V Shaped, 8 Feet - Strip Vinyl Dock Bumpers. Color: white. $28.99 #41305
|
|
Dock Bumper P Shaped, 8 Feet - Strip Vinyl Dock Bumpers. Color: white. $44.99 #41307
|
|
Dock Bumper P Shaped Corner w/ Joiner
- Made of tough vinyl. Use with Dock Bumper P Shaped (#41307) above. Joiner ends
insert into the strip bumper for a neat, continuous look. Color:
white. $16.99 #41302 |
|
Dock Bumper Solid Corner - Made of tough vinyl. Can be mounted to wood or metal docks. Length: 10" /side. Color: white. $16.99 #41003
|
|
Boat Shield, 4 Feet - This
extruded U.V. Stabilized polyethylene foam bumper is contoured at the
back so it can be mounted both horizontally on your dock or vertically
on pilings. The beveled edge helps deflect your boats' fenders so they
do not catch under the profile. The light gray color matches up with
the natural color of weathered wood. Stainless steel screws and washers
included. 48" x 2 3/4" x 5". $28.99 #100703
|
|
DocKushion, 4 Feet - The
ultimate in protection systems. No need for fenders any more! This
revolutionary new design incorporates a soft expanded polypropylene
core surrounded by integral skin foam. this creates the softest but most
durable bumper you can treat your boat to. A molded in backer allows
strong secure mounting. Unique male and female sockets at the ends make
joining the pieces a snap for a seamless look. U.V. Stabilized classic
gray color will enhance the look of your dock. 48" x 2" x 4".
$65.99 #115003
|
|
DocKap
- End caps
complete your system for a professional looking job. U.V.
Stabilized classic gray color will enhance the look of your dock. 2" x
2" x 4". $27.99 #115203 |
|
Inflatable Dock Wheels, Corner Mount
- Smooth rolling wheels offer substantial dock cushioning and feature
molded-in valves to adjust the level of firmness. Heavy duty hot dipped
galvanized hardware mounts securely to the dock. Guide boats into your
slip easily, regardless of wind and current conditions. Color: white.
- 9" wheel - $69.99 #950783
- 12" wheel - $124.99 #950723
|
|
ProTect Straight Bumper -
This Heavy Duty Straight Bumper is manufactured from MPR (Melt
Processable Rubber). It has excellent shock absorption qualities and
will not mark or mar the hull of your boat. 15" x 2 1/4" x 1 1/2".
Color: white. $13.99 #105803
|
|
UltraGard - This Bumper is
manufactured from highest quality marine grade vinyl and offers the
ultimate in cushioning of impacts from your boat. Molded in ribs on the
interior of the UltraGard ensure it is very soft, but durable and will
not collapse. The back has a slight radius allowing for easy mounting
on pilings as well. 35" x 2 1/4" x 5" Color: white. $35.99 #100803
|
|
Torpedo Bumpers - These large, durable bumpers add an attractive and functionally rugged
cushion to the leg pipes of your docking system. Each weighs a rugged 2.7
lb. and measures 18” tall with a diameter of 5”. Place them on dock leg
pipes over the mounting brackets to prevent damaging your watercraft
from protruding bolts. Color: white. $29.49 #911103
|
|
Shore Power Clip - The safe
and reliable way to secure electrical shore power cords in high traffic
areas. Easy to install and use, the Shore Power Clip is designed to
hold a 30 Amp marine power cord in its low profile "toe-friendly"
shape. 4 Pcs /Bag. $8.49 #191200
|
|
Ladder - Quick Release Aluminum -
Manufactured with 1” heavy wall aluminum tubing. All assembly hardware
is stainless steel. A quick release kit is included. Simply tilt the
ladder up and slide it out for storage and cleaning, or mount the
ladder permanently with it's pre-drilled holes.
- 3-Step - $227.99 #200303
- 4-Step - $261.99 #200403
|
|
Ladder
- Bright White Galvalume or Brushed Stainless Steel finish - Heavy 1-1/2” tubing ensures a
positive grip. Stainless Steel hardware is included.
- 3-Step, White Galvalume finish - $167.99 #210303
- 3-Step, Brushed Stainless Steel finish - $304.99 #220303
- 4-Step, White Galvalume finish - $209.99 #210403
- 4-Step, Brushed Stainless Steel finish - $374.99 #220403
- 5-Step, White Galvalume finish - $251.99 #210503
- 1-Step Ladder Extension - $48.99 #210103
- 2-Step Ladder Extension - $95.99 #210203
|
|
Ladder - Stainless Steel Flip-Up -
Brushed Stainless Steel finish. Heavy 1-1/2” tubing ensures a positive
grip. Hinged design allows the ladder to conveniently flip out of the
water when not in use. Stainless Steel hardware is included.
- 3-Step - $348.99 #221303
- 4-Step - $418.99 #221403
|
|
Classic Cleats - Cast from solid aluminum and powder coated to last. Distinctive and highly functional.Color: white.
- 4-1/2" - $20.49 #250407
- 6-1/2" - $29.99 #250607
|
|
Flip Up Cleats
- These cleats fold down to a low profile base
and conveniently flip up for easy use. All surfaces are smooth and
rounded. Made from marine grade aluminum and white polyester powder
coated. Use on small boats or personal watercraft. Color: white.
- 3-1/2" - $10.99 #260309
- 6" - $21.49 #260609
- 8" - $35.49 #260809
|
|
Portable InstaCleat - This strong,
yet lightweight cast aluminum portable cleat features a polyester
powder coat finish and stainless steel T-bar. Install securely in
seconds and use whenever cleats are missing or in an inconvenient
location. Also provides extra security in rough weather for spring
lines. Color: white. $25.49 #270503
|
|
Recessed Cleat - This 1"
deep recessed cleat is flush mounted with a flip up ring. When not in
use it leaves nothing for you to trip over. Simply use a 4" hole saw
for mounting and bolt to your dock. Polyester powder coated for a
durable finish. Color: white. $11.99 #271003
|
|
Our Premium Whips are exceptionally strong and
will not obstruct your waterfront view. These quality mooring whips,
act as springs to maintain your boat at a safe, convenient distance
from your dock and prevent impacts from waves or the wakes of passing
watercraft. Unlike other solid rod fiberglass products, our
whips start with a solid rod and then are manufactured in multi-stages
with cross-wound fiberglass to give these mooring whips the necessary
strength and flex to retain the boats’ position and prevent over flexing
of the whip. Each whip includes our exclusive “Plug & Socket”
design for quick and easy separation and our solid cast aluminum base
with built-in cleat, ring and thumb screw for easy removal and
convenient storage of the whips.
- 8' Whip, set of 2. 2,500lb. capacity - each set
$289.99. SALE $229.99. #320003
- 12' Whip, set of 2. 5,000lb. capacity - each set
$389.99. SALE $339.99. #340003
- 14' Whip, set of 2. 10,000lb. capacity - each set
$439.99. SALE $399.99. #360003
- 16' Whip, set of 2. 20,000lb. capacity - each set
$499.99. SALE $429.99. #380003
|
* Restrictions Apply -- See Shipping Information in our Online Store.
Pricing is only guaranteed for online purchases that are shipped.
© 2014 Dowsar Yacht Sales Limited. All rights reserved.
|